PDA

Afficher la version complète : [Non Réglé] Installer un graveur en Firewire



galagann
21/11/2004, 11h32
Bonjour,

Je ne peux pas dire grand chose sur ce sujet, mais j'ai un graveur DVD en Firewire et je voudrai le faire fonctionner sous SuSE. Mon extention Firewire est bien prise en compte sous SuSE :
Alionet:~ # lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev80)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
0000:00:08.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
0000:00:10.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev10)
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e)
0000:00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e)
0000:00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40)
0000:00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 20)
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev51)
0000:01:00.0 VGA compatible controller: S3 Inc. VT8636A [ProSavage KN133] AGP4XVGA Controller (TwisterK) (rev 01)
Alionet:~ #
Le module i1394 (Firewire) est bien ouvert au boot !

Quelqu'un a une solution ???

Merci d'avance http://www.alionet.org/style_emoticons/<#EMO_DIR#>/biggrin.gif

Edit : En USB cela donne celà, mais je voudrai le faire fonctionner en Firewire car sur mon portable c'est encore de l'USB1 http://www.alionet.org/style_emoticons/<#EMO_DIR#>/laugh.gif
usb 2-1: USB disconnect, address 2
usb 2-1: new full speed USB device using address 3
usb 2-1: Product: Mass Storage Device
usb 2-1: Manufacturer: Prolific Technology Inc.
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: _NEC Model: DVD_RW ND-2510A Rev: 2.F8
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.

galagann
12/04/2005, 19h45
Toujours la même chose :

SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
scsi0 : SCSI emulation for IEEE-1394 SBP-2 Devices
ieee1394: sbp2: Logged into SBP-2 device
ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048]
Vendor: _NEC Model: DVD_RW ND-2510A Rev: 2.F9
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5