Aller au contenu principal

Messages

Cette espace vous permet de voir toutes les Messages réalisées par ce membre. Vous ne pouvez voir que les Messages réalisées dans les espaces auxquels vous avez accès.

Messages - croquette38

1
Général / Re : Gros doute sur ma partition disque dur
Hello, de retour de week-end, je vous remercie encore pour les réponses !

- je vais m'atteler à la création d'un point de montage pour mon disque de stockage (pas ds l'immédiat mais bientôt) et je reviendrai vers vous pour vos lumières si jamais ça coince

- concernant la commande smartctl voici le résultat ci-dessous, pour chaque disque, et je ne vous cache pas que c'est du chinois à mes yeux !!! Mais comme c'est marqué "test result : PASSED" je suppose que c'est plutôt positif (non ?)

smartctl -a /dev/sda
smartctl 7.2 2021-09-14 r5237 [x86_64-linux-5.14.21-150500.55.7-default] (SUSE RPM)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     LDLC F6+M.2 480
Serial Number:    09042219C0012
Firmware Version: S0424A0
User Capacity:    480 103 981 056 bytes [480 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      M.2
TRIM Command:     Available, deterministic, zeroed
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Aug  7 11:15:07 2023 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x02)   Offline data collection activity
               was completed without error.
               Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)   The previous self-test routine completed
               without error or no self-test has ever
               been run.
Total time to complete Offline
data collection:       (  120) seconds.
Offline data collection
capabilities:           (0x11) SMART execute Offline immediate.
               No Auto Offline data collection support.
               Suspend Offline collection upon new
               command.
               No Offline surface scan supported.
               Self-test supported.
               No Conveyance Self-test supported.
               No Selective Self-test supported.
SMART capabilities:            (0x0002)   Does not save SMART data before
               entering power-saving mode.
               Supports SMART auto save timer.
Error logging capability:        (0x01)   Error logging supported.
               General Purpose Logging supported.
Short self-test routine
recommended polling time:     (   2) minutes.
Extended self-test routine
recommended polling time:     (  10) minutes.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x0032   100   100   050    Old_age   Always       -       0
  5 Reallocated_Sector_Ct   0x0032   100   100   050    Old_age   Always       -       3
  9 Power_On_Hours          0x0032   100   100   050    Old_age   Always       -       4763
 12 Power_Cycle_Count       0x0032   100   100   050    Old_age   Always       -       646
160 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       1
161 Unknown_Attribute       0x0033   100   100   050    Pre-fail  Always       -       95
163 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       11
164 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       10103
165 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       45
166 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       4
167 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       20
168 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       7000
169 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       100
175 Program_Fail_Count_Chip 0x0032   100   100   050    Old_age   Always       -       0
176 Erase_Fail_Count_Chip   0x0032   100   100   050    Old_age   Always       -       0
177 Wear_Leveling_Count     0x0032   100   100   050    Old_age   Always       -       0
178 Used_Rsvd_Blk_Cnt_Chip  0x0032   100   100   050    Old_age   Always       -       3
181 Program_Fail_Cnt_Total  0x0032   100   100   050    Old_age   Always       -       0
182 Erase_Fail_Count_Total  0x0032   100   100   050    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   050    Old_age   Always       -       50
194 Temperature_Celsius     0x0022   100   100   050    Old_age   Always       -       42
195 Hardware_ECC_Recovered  0x0032   100   100   050    Old_age   Always       -       205819
196 Reallocated_Event_Count 0x0032   100   100   050    Old_age   Always       -       1
197 Current_Pending_Sector  0x0032   100   100   050    Old_age   Always       -       3
198 Offline_Uncorrectable   0x0032   100   100   050    Old_age   Always       -       1
199 UDMA_CRC_Error_Count    0x0032   100   100   050    Old_age   Always       -       11
232 Available_Reservd_Space 0x0032   100   100   050    Old_age   Always       -       95
241 Total_LBAs_Written      0x0030   100   100   050    Old_age   Offline      -       80819
242 Total_LBAs_Read         0x0030   100   100   050    Old_age   Offline      -       107397
245 Unknown_Attribute       0x0032   100   100   050    Old_age   Always       -       94248

SMART Error Log Version: 1
Warning: ATA error count 0 inconsistent with error log pointer 1

ATA Error Count: 0
   CR = Command Register [HEX]
   FR = Features Register [HEX]
   SC = Sector Count Register [HEX]
   SN = Sector Number Register [HEX]
   CL = Cylinder Low Register [HEX]
   CH = Cylinder High Register [HEX]
   DH = Device/Head Register [HEX]
   DC = Device Command Register [HEX]
   ER = Error register [HEX]
   ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 0 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ea 00 00 00 00 00 a0 08      00:00:00.000  FLUSH CACHE EXT
  b0 da 00 00 4f c2 00 08      00:00:00.000  SMART RETURN STATUS
  b0 d0 01 00 4f c2 00 08      00:00:00.000  SMART READ DATA
  b0 d5 01 06 4f c2 00 08      00:00:00.000  SMART READ LOG
  b0 d5 01 01 4f c2 00 08      00:00:00.000  SMART READ LOG

Error -1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  00 00 00 00 00 00 00   at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 08 98 e8 b8 3c 00 00      00:00:00.000  WRITE FPDMA QUEUED
  61 20 c0 60 d4 13 00 00      00:00:00.000  WRITE FPDMA QUEUED
  61 20 c0 60 d4 13 00 00      00:00:00.000  WRITE FPDMA QUEUED
  61 20 c0 60 d4 13 00 00      00:00:00.000  WRITE FPDMA QUEUED
  61 20 c0 60 d4 13 00 00      00:00:00.000  WRITE FPDMA QUEUED

Error -2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ea 00 00 00 00 00 a0 08      00:00:00.000  FLUSH CACHE EXT
  b0 da 00 00 4f c2 00 08      00:00:00.000  SMART RETURN STATUS
  b0 d0 01 00 4f c2 00 08      00:00:00.000  SMART READ DATA
  b0 d5 01 06 4f c2 00 08      00:00:00.000  SMART READ LOG
  b0 d5 01 01 4f c2 00 08      00:00:00.000  SMART READ LOG

Error -3 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ea 00 00 00 00 00 a0 08      00:00:00.000  FLUSH CACHE EXT
  b0 da 00 00 4f c2 00 08      00:00:00.000  SMART RETURN STATUS
  b0 d0 01 00 4f c2 00 08      00:00:00.000  SMART READ DATA
  b0 d5 01 06 4f c2 00 08      00:00:00.000  SMART READ LOG
  b0 d5 01 01 4f c2 00 08      00:00:00.000  SMART READ LOG

Error -4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  00 00 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  b0 d0 01 00 4f c2 00 08      00:00:00.000  SMART READ DATA
  b0 d1 01 01 4f c2 00 08      00:00:00.000  SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
  b0 da 00 00 4f c2 00 08      00:00:00.000  SMART RETURN STATUS
  b0 d5 01 00 4f c2 00 08      00:00:00.000  SMART READ LOG
  b0 d5 01 01 4f c2 00 08      00:00:00.000  SMART READ LOG

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      4762         -
# 2  Short offline       Completed without error       00%      4761         -
# 3  Short offline       Completed without error       00%      4754         -
# 4  Short offline       Completed without error       00%      4753         -
# 5  Short offline       Completed without error       00%      4750         -
# 6  Short offline       Completed without error       00%      4740         -
# 7  Short offline       Completed: read failure       90%      4717         348636000
# 8  Short offline       Completed: read failure       90%      4692         339234912
# 9  Short offline       Completed without error       00%      4668         -
#10  Short offline       Completed without error       00%      4644         -
#11  Short offline       Completed without error       00%      4620         -
#12  Short offline       Completed without error       00%      4602         -
#13  Short offline       Completed without error       00%      4599         -
#14  Short offline       Completed without error       00%      4592         -
#15  Short offline       Completed without error       00%      4590         -
#16  Short offline       Completed without error       00%      4586         -
#17  Short offline       Completed without error       00%      4585         -
#18  Short offline       Completed without error       00%      4583         -
#19  Short offline       Completed without error       00%      4580         -
#20  Short offline       Completed without error       00%      4579         -
#21  Extended offline    Completed: read failure       90%      4577         343034784
3 of 3 failed self-tests are outdated by newer successful extended offline self-test # 1

Selective Self-tests/Logging not supported





smartctl -a /dev/sdb
smartctl 7.2 2021-09-14 r5237 [x86_64-linux-5.14.21-150500.55.7-default] (SUSE RPM)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate BarraCuda 3.5 (CMR)
Device Model:     ST1000DM010-2EP102
Serial Number:    ZN198AE3
LU WWN Device Id: 5 000c50 0c2c6a7a1
Firmware Version: CC43
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Aug  7 11:16:29 2023 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)   Offline data collection activity
               was never started.
               Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 243)   Self-test routine in progress...
               30% of test remaining.
Total time to complete Offline
data collection:       (    0) seconds.
Offline data collection
capabilities:           (0x73) SMART execute Offline immediate.
               Auto Offline data collection on/off support.
               Suspend Offline collection upon new
               command.
               No Offline surface scan supported.
               Self-test supported.
               Conveyance Self-test supported.
               Selective Self-test supported.
SMART capabilities:            (0x0003)   Saves SMART data before entering
               power-saving mode.
               Supports SMART auto save timer.
Error logging capability:        (0x01)   Error logging supported.
               General Purpose Logging supported.
Short self-test routine
recommended polling time:     (   1) minutes.
Extended self-test routine
recommended polling time:     ( 102) minutes.
Conveyance self-test routine
recommended polling time:     (   2) minutes.
SCT capabilities:           (0x1085)   SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   078   063   006    Pre-fail  Always       -       59353828
  3 Spin_Up_Time            0x0003   097   096   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       643
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   074   060   045    Pre-fail  Always       -       28648061
  9 Power_On_Hours          0x0032   095   095   000    Old_age   Always       -       4991
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       643
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   068   057   040    Old_age   Always       -       32 (Min/Max 21/33)
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       718
194 Temperature_Celsius     0x0022   032   004   000    Old_age   Always       -       32 (0 4 0 0 0)
195 Hardware_ECC_Recovered  0x001a   004   001   000    Old_age   Always       -       59353828
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       4972h+57m+20.655s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       2764551784
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       4529769154

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Self-test routine in progress 30%      4991         -
# 2  Short offline       Completed without error       00%      4989         -
# 3  Short offline       Completed without error       00%      4981         -
# 4  Short offline       Completed without error       00%      4980         -
# 5  Short offline       Completed without error       00%      4964         -
# 6  Short offline       Completed without error       00%      4940         -
# 7  Short offline       Completed without error       00%      4916         -
# 8  Short offline       Completed without error       00%      4892         -
# 9  Short offline       Completed without error       00%      4868         -
#10  Short offline       Completed without error       00%      4844         -
#11  Short offline       Completed without error       00%      4826         -
#12  Short offline       Completed without error       00%      4822         -
#13  Short offline       Completed without error       00%      4814         -
#14  Short offline       Completed without error       00%      4812         -
#15  Short offline       Completed without error       00%      4808         -
#16  Short offline       Completed without error       00%      4806         -
#17  Short offline       Completed without error       00%      4803         -
#18  Short offline       Completed without error       00%      4800         -
#19  Short offline       Completed without error       00%      4797         -
#20  Extended offline    Completed without error       00%      4796         -
#21  Short offline       Completed without error       00%      4778         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.











2
Général / Re : Gros doute sur ma partition disque dur
Hello,

un grand merci pour ta réponse !

Sur mon ordi, j'ai 2 disques durs :

- le 480 Go (avec les fameux 6 secteurs endommagés > donc je m'inquiète pas outre mesure, ouf, c'est sain, c'est cool !!!), qui a 3 partitions, et qui curieusement s'appelle maintenant sdb dans Yast (cf capture d'écran)

- le 1 To qui me sert d'archivage, qui s'appelle sda. Pour y accéder, dans "Fichiers" je clique sur "Autre emplacement" et là, il me demande mon mdp root car il me dit que le disque n'est pas monté. Donc je rentre le mdp et roule ma poule. Pour celui là, si je comprends bien, le souci c'est qu'il n'y a pas de point de montage, et il faut le créer : est-ce que c'est possible avec l'utilitaire "Disques" de Gnome ou le partitionneur de Yast ?

Ensuite j'ai tout un tas de ports USB qui s'affichent dans l'utilitaire "Disques" (cf autre capture d'écran). Dans Yast, comme j’avais une clé USB branchée au moment de la capture d’écran, elle est affichée comme sdc.

Concernant le système de fichiers, je copie-colle ce que j'ai depuis Yast :

Disque dur 1 To, soit "sda" :

Périphérique :
Périphérique : /dev/sda1
Taille : 0.91 TiB
Chiffrement : Non
Chemin d'accès au périphérique 1 : pci-0000:00:17.0-ata-6-part1
Chemin d'accès au périphérique 2 : pci-0000:00:17.0-ata-6.0-part1
ID du périphérique 1 : ata-ST1000DM010-2EP102_ZN198AE3-part1
ID du périphérique 2 : scsi-0ATA_ST1000DM010-2EP1_ZN198AE3-part1
ID du périphérique 3 : scsi-1ATA_ST1000DM010-2EP102_ZN198AE3-part1
ID du périphérique 4 : scsi-35000c500c2c6a7a1-part1
ID du périphérique 5 : scsi-SATA_ST1000DM010-2EP1_ZN198AE3-part1
ID du périphérique 6 : wwn-0x5000c500c2c6a7a1-part1
ID de partition : Linux
Système de fichiers :
Type : XFS
Point de montage :
Monté par :
Options de montage :
Étiquette : ARCHIVES
UUID : dd3ac02d-b3f9-452b-a14a-365d1ead5bba


Ensuite, pour le disque dur 480 Go, par partition :
Partition : /dev/sdb1
Périphérique :
Périphérique : /dev/sdb1
Taille : 0.50 GiB
Chiffrement : Non
Chemin d'accès au périphérique 1 : pci-0000:00:17.0-ata-1-part1
Chemin d'accès au périphérique 2 : pci-0000:00:17.0-ata-1.0-part1
ID du périphérique 1 : ata-LDLC_F6+M.2_480_09042219C0012-part1
ID du périphérique 2 : scsi-0ATA_LDLC_F6+M.2_480_09042219C0012-part1
ID du périphérique 3 : scsi-1ATA_LDLC_F6+M.2_480_09042219C0012-part1
ID du périphérique 4 : scsi-SATA_LDLC_F6+M.2_480_09042219C0012-part1
ID de partition : Partition système EFI
Système de fichiers :
Type : FAT
Point de montage : /boot/efi
Monté par : UUID
Options de montage : utf8
Étiquette :
UUID : 2DFA-AF77


Partition : /dev/sdb2
Périphérique :
Périphérique : /dev/sdb2
Taille : 431.13 GiB
Chiffrement : Non
Chemin d'accès au périphérique 1 : pci-0000:00:17.0-ata-1-part2
Chemin d'accès au périphérique 2 : pci-0000:00:17.0-ata-1.0-part2
ID du périphérique 1 : ata-LDLC_F6+M.2_480_09042219C0012-part2
ID du périphérique 2 : scsi-0ATA_LDLC_F6+M.2_480_09042219C0012-part2
ID du périphérique 3 : scsi-1ATA_LDLC_F6+M.2_480_09042219C0012-part2
ID du périphérique 4 : scsi-SATA_LDLC_F6+M.2_480_09042219C0012-part2
ID de partition : Linux
Système de fichiers :
Type : Btrfs
Point de montage : /
Monté par : UUID
Options de montage :
Étiquette :
UUID : 0f1f8fbb-8929-4479-ad65-31b632eb63eb
Niveau de RAID : SINGLE
Niveau de RAID des métadonnées : SINGLE
Périphériques utilisés :
/dev/sdb2


Partition : /dev/sdb3
Périphérique :
Périphérique : /dev/sdb3
Taille : 15.50 GiB
Chiffrement : Non
Chemin d'accès au périphérique 1 : pci-0000:00:17.0-ata-1-part3
Chemin d'accès au périphérique 2 : pci-0000:00:17.0-ata-1.0-part3
ID du périphérique 1 : ata-LDLC_F6+M.2_480_09042219C0012-part3
ID du périphérique 2 : scsi-0ATA_LDLC_F6+M.2_480_09042219C0012-part3
ID du périphérique 3 : scsi-1ATA_LDLC_F6+M.2_480_09042219C0012-part3
ID du périphérique 4 : scsi-SATA_LDLC_F6+M.2_480_09042219C0012-part3
ID de partition : Swap Linux
Système de fichiers :
Type : Swap
Point de montage : swap
Monté par : UUID
Options de montage :
Étiquette :
UUID : 4139c811-af83-42f0-9ef4-2f9e342f60e4


Voilou, j'espère que j'ai à peu près donné les informations nécessaires pour savoir si j'ai foiré ou non (suspens)

... et encore un immense merci à toutes et à tous pour la patience et la pédagogie :)





3
Général / Gros doute sur ma partition disque dur
Bonjour à toutes et à tous,

Hier, j'avais posté un message parce que j'avais un problème d'appli qui ne se lançait pas (sous Leap 15.4).

Dans un coup de folie, j'ai installé 15.5 et tout s'est bien passé, j'en suis ravie - j'ai fait l'installation complète depuis une clé usb bootable. La partie délicate c'est au moment de choisir la partition, et là j'ai des gros doutes sur ce que j'ai choisi.

J'ai 2 disques durs, 1 SSD sur lequel je mets mes fichiers courants de travail (480 Go) = sda, et 1 disque dur de 1 To qui me sert pour l'archivage =sdb.
Je n'ai pas partitionné ce dernier, seulement sda, qui présente trois partitions. Est-ce que cela vous semble correct ? Ou bien j'ai fait une boulette ?

Quand j'utilise la commande lsblk voici ce que j'obtiens :

NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTS
sda      8:0    0 447,1G  0 disk
├─sda1   8:1    0   512M  0 part /boot/efi
├─sda2   8:2    0 431,1G  0 part /var
│                                /tmp
│                                /root
│                                /usr/local
│                                /srv
│                                /opt
│                                /home
│                                /boot/grub2/x86_64-efi
│                                /boot/grub2/i386-pc
│                                /.snapshots
│                                /
└─sda3   8:3    0  15,5G  0 part [SWAP]
sdb      8:16   0 931,5G  0 disk
└─sdb1   8:17   0 931,5G  0 part
sdc      8:32   1     0B  0 disk
sdd      8:48   1     0B  0 disk
sde      8:64   1     0B  0 disk
sdf      8:80   1     0B  0 disk
sdg      8:96   1     0B  0 disk

Autre question, je ne sais pas si je dois m'inquiéter : quand j'ouvre "Disques" :
Modèle : LDLC F6+M.2 480 (S0424A0)
Numéro de série : LDLC F6+M.2 480 (S0424A0)
Estimation : Le disque est sain, 6 secteurs endommagés (42°C / 108° F)    Gloups.
Taille : 480 Go (480 103 981 056 octets)
Partitionnement : Table des partitions GUID


Un grand merci par avance pour votre aide !
4
Programmes et logiciels / Re : "Paramètres" ne se lance pas
Bonjour, mille mercis pour vos réponses !

Oui j'avais bien fait une mise à jour il y a quelques jours... + installé un truc qui s'appelle SoftMaker Office parce que j'avais besoin de réouvrir des vieux fichiers .ppt qui étaient tout éclatés quand je les ouvrais avec LibreOffice Impress.

Alors effectivement la commande gnome-control-center dans un terminal lançait bel et bien Paramètres. Mais toujours pas quand le cliquais dessus. Entre-temps, je me suis rendue compte que le même souci affectait aussi le logiciel "Presentations NX" de SoftMaker.

Et comme je n'avais pas vu vos réponses immédiatement... J'ai fait une grosse sauvegarde, et j'ai installé Leap 15.5, et le problème est résolu. J'ai probablement sorti le marteau pour écraser une mouche, mais cela faisait quelque temps que je voulais faire l'upgrade.

 Je suis bien désolée de vous avoir sollicités pour rien, mais encore un très grand merci d'avoir répondu à l'appel :)
5
Programmes et logiciels / "Paramètres" ne se lance pas
Bonjour à toutes et à tous,

Je rencontre un souci avec OpenSUSE Leap 15.4 depuis quelques jours : je n'arrive pas à lancer le logiciel Paramètres de Gnome.
Il fait mine de se lancer, l'onglet s'ouvre dans la barre en haut de l'écran, et ensuite disparaît.
Du coup c'est très pénible !!! Quelqu'un aurait déjà rencontré un problème similaire ? Je suis simple utilisatrice sympathisante, me compétences demeurent très limitées. Et en termes de recherche, avec le mot clé "Paramètres", comment vous dire, j'ai un peu l'impression de chercher une aiguille dans une gigatonne de foin.

Mille mercis par avance si vous avez des pistes ou des idées :)
6
Présentations / Re : bonjour à tous
Salut, merci de l'accueil ! Je travaille dans  un bureau d'étude en archéologie préventive. Perso je trouve que les outils sont très bien, mais le souci c'est quand on doit collaborer avec d'autres entreprises qui utilisent des logiciels propriétaires (suite Adobe par ex)... des fois c'est un peu galère. Mais hormis ça, cela me convient très bien.
a+
7
Présentations / bonjour à tous
Salut tout le monde,

je m'inscris sur ce forum car j'ai enfin franchi le pas d'installer Opensuse sur mon ordi perso (je l'avais déjà au boulot) (leap 15.1), depuis quelques semaines.

J'espère trouver ici une mine d'or d'infos divers et variées et pouvoir progresser pour apprendre à me débrouiller en cas de pépin.

Bonne journée à tous et surtout bon week-end !